Set the heater: the perfect hot water temperature

• Set heating
  • energy efficiency
  • environmental impact
  • maintenance
  • deflate
• Correct hot water temperature

More and more homeowners worry about the regulation of the hot water temperature. Incorrectly set heaters clearly gnaw on the purse or cause in the cold season about insufficient heat development within the premises. For this reason, it is important to know how to adjust the heater to reach the ideal temperature. Since the boiler is not so easy to see through, you will find the necessary information for setting here.

Set heating

Why is the right hot water temperature important ">

energy efficiency

If you set the heating to be too hot or too cold, you will have to pay more heating costs in the long term. Incorrectly set hot water temperatures either ensure that the water is not sufficiently hot enough and therefore higher quantities are sent into the radiator in order to generate the necessary heat. If the temperature values ​​are set too high, the water in the supply line will always be heated to a great extent, which consumes a great deal of energy. Both variants gnaw on the purse and either you are permanently too warm or too cold.

environmental impact

As you may have read in the previous point, the energy efficiency drops significantly if the temperature of the heater has not been set correctly. In addition, the wrong temperature will put a greater burden on the environment as you use more energy. The higher the value set up to now differs from the recommended hot water temperature, the higher the environmental impact of your heating system.

maintenance

Excessively high temperatures over a long period of time may cause the pipes or radiators to be damaged . This is due to the constant heating of the water, which is then fed into the radiator and in the return is still too hot in many cases. Therefore, a corresponding temperature is needed over which the flow and return are not too hot.

You see, the disadvantages are serious, especially if you have to heat large rooms. Precisely for this reason it is so important to set the heater properly. This is especially noticeable when people put the heating on the highest level because they think it would be warmer.

However, the markings on the thermostat are not the stage but only the time required to heat the water. The higher the level is set, the faster it gets warm, and the heater will appear warmer in intensity. If you wildly move the thermostat on a wrongly adjusted heater, the worse the above mentioned disadvantages become.

Tip: Setting the correct temperature of the hot water is even more important if your pipes for the heating and the water of your shower and taps converge in the living areas. Without the right temperature, dangerous germs and bacteria like Legionella can settle in the water and lead to a disease.

deflate

If you want to adjust your heating, you must first let the air out of the radiator and the pipes. Sometimes hear a clucking or knocking sound from your heater ">

The following items are needed to bleed the heater:

• 1 bleed key (about 2 Euro per piece)
• 1 bowl
• 1 cloth (absorbent)

The vent key is specially shaped and allows easy opening of the vent valve of the heater. Once you have secured the key, remove the air from the radiator with the following steps.

• Set the radiator to the highest level
• to run for a few minutes
• then turn it back completely
• do not turn it on anymore
• wait a few moments
• The vent valve is usually opposite the thermostat
• Turn the valve opening in the direction of the bowl
• now set the bleeding key
• turn maximum half a turn counterclockwise
• a stream of air would have to be heard
• wait until no more air is heard
• only water should come out of the valve
• close afterwards
• Mop up spilled water

Now your heater is vented. Venting before adjusting the temperature is important so that the heater can run completely without negative side effects, which in turn saves energy. Air in the heater must also be heated and ensures that the water is displaced. Thus, this sometimes does not reach all places in the radiator. The venting of a floor heating, in contrast, happens at the heating system and is much harder to implement. Here you should rely on the expertise of an installer.

Tip: Dumping the air, especially for older radiators, can provide significantly better heat output without wasting energy.

Correct hot water temperature

Set heating: correct hot water temperature

If you want to set the right flow temperature, you first need access to the heating system in the house. If you are the owner of the house, this is no problem at all. If you live in a rented apartment, this task will be taken over by the landlord or the company renting the apartments.

In rental houses, access to the heating system can sometimes be closed off. If so, you need to contact your landlord to initiate further action. Adjusting the heating is very easy and happens directly at the heating system . If available, use the operating instructions for the system. Now it is up to the setting of the hot water temperature, for which the following values ​​are necessary.

• Transport heat losses
• Insulating properties of the premises
• Surfaces of the heaters

All these values ​​will be considered by a heating installer in order to set the exact flow temperature. Of course, as a normal consumer this is not really possible because you are missing the measuring devices. For this reason, the classic defaults that have been established over the years, if you yourself have no knowledge in this area, or if the installation by an installer is out of the question for you at the moment, remain with you. Below are the default values ​​for the hot water temperature that you set on your heater.

• Radiator: 60 ° C - 65 ° C
• Underfloor heating: 55 ° C

Underfloor heating uses a different type of heat distribution and often occupy a much larger area than radiators, which explains the lower temperature. The biggest problem with these values ​​is the fact that external factors are not taken into account. Location, nature of the house and the prevailing weather conditions can ensure that higher temperatures must be set. This is not noticed by the normal consumer in most cases. These values ​​will work more effectively if you also set the return temperature to the default values.

• Radiator: 40 ° C
• Underfloor heating: 45 ° C

The right return temperature ensures significantly better energy efficiency. There is a problem with this variant. Since neither the rooms nor the location of the house itself is included in the determination of the ideal flow temperature when using the standard values, the heating can still use too much energy. Exactly for this purpose, the commissioning of a professional offers. Alternatively, using a heating curve, you can adjust the temperature even more precisely, if you know how to apply it.