Clean the lint filter of the washing machine & help if it gets stuck

• Why clean lint filter "> Material
• Clean the lint filter: Instructions
• Opening the clamp: Instructions

The washing machine is one of today's essential home appliances. While they wash the dirty laundry clean, they collect a lot of lint and foreign bodies, which are then found in the lint filter. The cleaning of the lint filter is one of the most important maintenance on the washing machine and should not be neglected, otherwise the performance of the unit suffers.

Can you imagine a life without a washing machine? With their effectiveness and speed, a load of freshly laundered towels, linens or your favorite outfit is never far away. For this reason, it is important to maintain the performance of the washing machine, which is done by regular maintenance of the individual components. Especially the lint filter is often overlooked, although the cleaning of the screen can eliminate many problems with the washing machine and also positively affects the efficiency and performance. Failure to clean the lint filter can cause a variety of problems. The maintenance is not even really time consuming.

Why clean the lint filter?

The lint filter is an essential component inside the washing machine, which protects the lye pump from foreign bodies and thus allows the device to operate. For this reason, it is also called foreign body or small parts trap. The sieve catches all forms of small parts and foreign objects, including lint, buttons, handkerchiefs, money, hair, and even objects that should never ever get into the washing machine, such as nails. If too many objects collect in the sieve, the following symptoms may occur:

• Lint collect in the drum and deposit on the freshly laundered laundry
• Lye water is no longer pumped out properly, washing machine may leak or accumulate in the drum
• Washing machine can not be opened after the washing process
• it creates unpleasant odors
• the spin is not performed properly

In case of emergency, bigger problems can occur and the washing machine can give up the ghost. Therefore, you should never forget to clean the sieve. It is recommended to clean the sieve every three to six months, depending on the frequency of use. If you do a lot of washing, you should clean the sieve every three months.

material

In order to perform the cleaning effectively, some utensils are needed. These not only make the process easier, but help you to follow all the steps exactly.

You need this:

• screwdriver
• flat bowl
• mop
• Haarsieb
• Cleaning gloves
• microfiber cloth

More is not needed per se for cleaning the sieve, as it is easily achieved and does not require any special means for cleaning. In addition, the workload is low, just need to be done thoroughly to be effective.

Clean the lint filter: Instructions

The cleaning of the lint filter is quite fast and does not require any great knowledge. Proceed as follows:

Step 1: Locate the lint filter. This is accessible from the front of the washing machine and is located in the lower part, usually hidden on the right side behind a round or rectangular lid. This sits tight and must be opened with the help of the screwdriver. Here's why a slotted screwdriver is needed, because the Phillips screwdriver does not fit into the gap used to open the lid due to its shape. On some machines, the lids are equipped with a handle that can be opened without a screwdriver.

Step 2: After you have opened the lid, you will see the lint filter in front of you. This is in most cases round and has a handle, over which it is screwed out of the washing machine. Place the flat bowl directly under the strainer or under the appliance and make sure that no water can escape. This is especially important if you have a wooden floor in your bathroom. This is not so bad for tiles, but a lot of water can accumulate in this area.

Step 3: After placing the bowl, turn up the strainer. This often requires some strength, as it must be tight to seal the interior of the machine. Once the sieve has been opened, the water will drain in a surge and it is possible for lint and other debris to float in the water. You will be amazed what can sometimes be found in the water.

Step 4: Now remove the lint filter from the machine and clean it under running water. Beforehand, you should put the hair sieve over the drain so that the lint, hair and small parts do not get into the spout and clog it. Wear gloves for this step if you have sensitive skin.

Step 5: The coarse dirt is usually removed with the flowing water, but the numerous fluff are a little harder to remove. Take the microfiber cloth in your hand and rub the wire thoroughly from the outside to remove more lint.

6th step: After this superficial one is now the thorough cleaning. To do this, place the strainer in a water bath and soak it for some time before brushing the strainer with the brush. You can calm enough force in the cleaning, because the lint filter will endure that. At this step, make sure that every millimeter of the screen is brushed off, as numerous lint can accumulate in the mesh of the screen. Through this step, you dissolve the remaining dirt, which is not removed during the superficial cleaning.

Step 7: While cleaning with the brush, use the highest setting on your shower head or washbasin. The power of the water works effectively as an extra cleanser and helps to solve even the most stubborn lint. Just be careful not to splash yourself in the eye as the water hits the screen with a lot of pressure. Keep the hair sieve in the drain all the time.

Step 8: Clumps of hair are best solved with your fingers. If they are particularly stubborn, you should carefully cut with a pair of scissors or a knife the hair and remove. Hair is particularly damaging to the washing machine, as it can really wrap around any component, including the small parts trap.

Step 9: Then dry the wire with a microfiber cloth and place it in a place where it can dry completely. Residual moisture provides for new accumulations of lint, which should be avoided. Therefore, wait a while for the entire sieve to dry completely.

Step 10: In the meantime, you should clean the opening of the lint filter on the washing machine. Simply collect all fluff and small parts from the opening and remove stubborn dirt with the brush. Then you can put the sieve back into the machine and close the lid.

Tip: Optionally, you can use hair conditioner for cleaning and then rinse the sieve thoroughly with clear water. Flushing lightens the hair in the lint, making it easier for the entire procedure because straight hair can get stuck and difficult to remove.

Opening the clamp: Instructions

It can happen that the sieve jams and can not be opened in the usual way. The reason for this is usually a foreign body stuck in the sieve for this reason prevents the opening. Proceed as follows:

Step 1: At the beginning, the washing machine is disconnected from the electricity and closed. Now turn the tap on, because it must not get new water into the machine.

Step 2: Open the flap of the lint filter and drain the water over the hose. This is located directly next to the sieve and only has to be pulled out to empty the machine.

Step 3: Lay the washing machine on its side and open the cover on the floor. Here, a thick tube will be revealed, which connects the lint filter directly to the drain pump. This is now completed, which again leads to a lot of leaking water.

Step 4: Check the strainer and hose for foreign matter and remove them. If you can not solve the foreign object by hand, you should use a chopstick.

5th step: Finally, the washing machine is set up again, connected and cleaned the sieve.